Fax over IP: Making the Switch

March 11, 2015 Andrew Prokop

For the past ten-plus years enterprises have been making the switch from TDM to IP telephony. For the most part, this has involved replacing older digital telephones with IP equivalents while converting applications such as voice mail and IVR to a SIP interface. The benefits of these conversions are significant and you would be hard pressed to find a new PBX going in today without an IP infrastructure.

However, for most of the early 2000’s, trunks to the public switched telephone network (PSTN) remained unchanged with analog and ISDN/PRI trunks as the norm. Many carriers weren’t ready to deliver IP trunks and those that were didn’t deliver a complete set of features. All of this is starting to change, though, and enterprises are now replacing their TDM trunks with SIP trunks. As it was in the case of IP endpoints and applications, there are many benefits in switching to IP trunks. Unfortunately, there is one issue that tends to be forgotten. What do you do with all your fax lines? How do you convert them to IP? Is it possible to use SIP trunks for both voice and fax? Before these questions can be answered, a short primer on fax is necessary.

Fax (short for facsimile) has been around in one form or another since the 1920’s, but it wasn’t until the mid 1960’s that the Xerox Corporation introduced the first commercial fax machine. Faxes began as analog transmissions (Group 1 and Group 2) but that soon gave way to digital transmissions (Group 3 and Group 4) in the late 1960’s. Fax machines scan documents in the same manner as a frame of analog television, but those scans are then compressed and sent as modem signals across telephone lines. T.30 is used as the messaging protocol between fax machines. T.30 also supports a handshake mechanism whereby two fax machines exchange information about their capabilities to ensure that the sending fax machine sends data that the receiving fax machine understands and can ultimately display.

Faxes are sent and received as modem signals and different ITU standards exist for the different transmission speeds. For instance, V.27 defines faxes sent at 2400 or 4800 bits per second and V.34bis is used for faxes sent at 33600 bits per second. Modem signals and bit speeds are perfectly acceptable when you consider that an analog telephone line is a dedicated, circuit-switched connection with a consistent data flow. This is not the case with packet-switched IP which may suffer from jitter, delay, lost packets, and packets arriving out-of-order. So, how do you deal with this problem as your enterprise replaces analog and ISDN/PRI trunks with SIP trunks?




There are three schools of thought on this. The first is to create a quality of service network with none of the issues that can wreak havoc on real-time communications — in other words, no packet loss, no jitter, no latency, and no out-of-order packets. This allows you to run T.30 over a toll-quality, G.711 link and let your PBX convert the G.711 IP stream to the analog connection that your fax machine requires. This is known as “fax pass-through” and has been successfully used by many enterprises.

However, if your network isn’t nearly as clean as it should be, something else is needed. Enter T.38 – a Fax over IP (FoIP) protocol designed to packetize those modem signals in a way that overcomes the “flaws” in an IP network. It is T.38’s job to ensure that the fax packets will arrive in order, on time, and with as little jitter as possible. In most cases, a fax will begin as T.30 from the sending fax machine, be converted to T.38 by a fax gateway, transmitted across the IP network, and eventually be converted back to T.30 by a gateway (e.g. an Avaya TN2602 board within a G650 gateway) on the receiving end. Newer T.38 fax machines and fax servers exist which eliminate the need to convert to and from T.30, but since many of the older machines are in wide use today, gateways are still necessary.

The final possibility is to retain some TDM trunks strictly for fax. When considering the cost of gateways and line provisioning, this may be the best and cheapest solution.

As your enterprise makes its journey from TDM to SIP trunks, it is imperative that you examine your fax usage before committing to a particular SIP architecture. If fax is an important part of your business, you may want to look at T.38 from the standpoint of your communications infrastructure as well as your SIP trunks. Be aware that not all providers support T.38, so don’t fail to add that to your decision making process. In the end, though, it is possible to create a system that brings together the power of SIP with older, tried and true technologies such as fax.

About the Author

Andrew  Prokop

Director of Vertical Industries

Andrew Prokop has been heavily involved with SIP and VoIP technologies since the late 1990’s. He holds four United States patents in SIP and was on the team that developed Nortel’s carrier-grade SIP soft switch and SIP-based contact center. His software runs in products from Avaya and Genband. Andrew joined Arrow SI three years ago and through customer engagements, users groups, tradeshows, and webinars has been an evangelist for SIP as a transformational technology for enterprises and their customers. Andrew understands the needs of the enterprise and has the background and skills necessary to assist companies as they drive towards a world of dynamic and immersive communications.

Follow on Twitter More Content by Andrew Prokop
Previous Article
What is "The Cloud"?
What is "The Cloud"?

Next Article
SIP Security
SIP Security

Want to learn more?

Contact Us!